APC IP DSLAM Podręcznik Użytkownika Strona 159
- Strona / 603
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
151
Type: Create － Optional
Modify － Optional
Valid values: enable, disable
Default value: enable
Example:
$ create abond group intf ifname abond-0 groupid 1 minaggrrateupstrm 5
minaggrratednstrm 5 diffdelaytolupstrm 0 diffdelaytoldnstrm 0 asmprotocol
Disable sidformat EightBitSID maxrxbitrateratio 2 linkhecthrshld 1
numoflinksupforgrpup One asmirlthreshold 0 maxatmportusrate 0
Output
Verbose Mode On
Entry Created
ifname : abond-0 GroupId : 1
MinAggrRateUpstrm : 5 MinAggrRateDnstrm : 5
DiffDelayTolUpstrm : 4 DiffDelayTolDnstrm : 4
AsmProtocol : Disable SidFormat :
EightBitSID
MaxRxBitRateRatio : 2 LinkHecThreshold : 1
CtrlVpi : 0 CtrlVci : 0
NoOfLinksUpForGrpUp : One AsmIrlThreshold : 0
MaxAtmPortUsRate : 0
Oper Status : Up Admin Status : Enable
Verbose Mode Off:
Output Fields
Field Description
ifname
This specifies the interface index used for the ATM
Based Multi pair Bonding type of interfaces. Valid Value
is abond-X. Modification and deletion is not possible if
interface is enabled
GroupId
This specifies the group id configured for this interface.
This field is configured statically when the bonded group
is provisioned and must not be changed while the group
is in service. These fields may be used by an operator to
help identify mis-configuration or to assist in
management or debugging of the link.
MinAggrRateUpstrm
Minimum Aggregate Data Rate in bits per second in
Upstream direction.
MinAggrRateDnstrm
Minimum Aggregate Data Rate in bits per second in
Downstream direction.
DiffDelayTolUpstrm
The maximum differential delay among member links in
a bonding group in Upstream direction.
DiffDelayTolDnstrm
The maximum differential delay among member links in
a bonding group in downstream direction.
AsmProtocol
This parameter specifies whether Autonomous Status
Messages will be exchanged between CO and CPE. If it
is disabled then the group would be bonded statically
and CO would assume CPE to know all the
configuration parameters like SID format, number of
links in the bonded group and the links participating in
bonding. If it is enabled then CO would inform all these
parameters to CPE using Autonomous Status
Messages.
SidFormat
SID Format: 8 bit or 12 bit SID. Only 8 bit format is being
supported
MaxRxBitRateRatio
The maximum bit rate ratio among member links in a
bonding group in upstream direction.
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Powiązane produkty i podręczniki dla Networking APC IP DSLAM
Networking APC AP9606 Instrukcja Szybki Start
(20 strony)
(20 strony)
Networking APC AP9312TH Podręcznik Użytkownika
(32 strony)
(32 strony)
Networking APC AP9608 Instrukcja Instalacji
(32 strony)
(32 strony)
Networking APC 66123 Instrukcja Instalacji
(16 strony)
(16 strony)
Networking APC AP9630 Podręcznik Użytkownika
(85 strony)
(85 strony)
Networking APC IP DSLAM Podręcznik Użytkownika
(67 strony)
(67 strony)
Networking APC AP9630 Instrukcja Użytkownika
(117 strony)
(117 strony)
Networking APC AP9630 Instrukcja Użytkownika
(32 strony)
(32 strony)
Networking APC AP9224110 Dokumentacja
(16 strony)
(16 strony)
Networking APC AP9608 Dokumentacja
(9 strony)
(9 strony)
Networking APC AP9608 Instrukcja Użytkownika
(4 strony)
(4 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji