APC INROOM ACPSC3000 Instrukcje Operacyjne Strona 19
- Strona / 106
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
19InRoom Controller - Operating Instructions
Bus
ID
DIP-switch
1 2 3 4 5
0 0 0 0 0 0
1 1 0 0 0 0
2 0 1 0 0 0
3 1 1 0 0 0
4 0 0 1 0 0
5 1 0 1 0 0
6 0 1 1 0 0
7 1 1 1 0 0
8 0 0 0 1 0
9 1 0 0 1 0
10 0 1 0 1 0
11 1 1 0 1 0
12 0 0 1 1 0
13 1 0 1 1 0
14 0 1 1 1 0
15 1 1 1 1 0
16 0 0 0 0 1
17 1 0 0 0 1
18 0 1 0 0 1
19 1 1 0 0 1
20 0 0 1 0 1
21 1 0 1 0 1
22 0 1 1 0 1
23 1 1 1 0 1
24 0 0 0 1 1
25 1 0 0 1 1
26 0 1 0 1 1
27 1 1 0 1 1
28 0 0 1 1 1
29 1 0 1 1 1
30 0 1 1 1 1
31 1 1 1 1 1
IOC
bus ID:01
IOC
bus ID:03
IOC
bus ID:07
IOC
bus ID:08
IOC
bus ID:15
InRoom
Controller
bus ID:31
IOC
bus ID:17
IOC
bus ID:14
RS 485
56 57 58 59 56 57 58 59
LOW
HIGH
The maximum configuration consists of 16 cooling units with an I/O controller and an
InRoom Controller. One of the features of the controller is its facility for bus operation.
All that is needed is a shielded cable with two lines twisted in pairs, which are connec-
ted from unit to unit at the terminals 56-59 of each I/O controller (IOC). In the example
below the bus termination of the two units that form the end of the bus (IOC 01 and
IOC 17) must be enabled.
The example of a RS485 bus shows a typical application with 7 IOCs and 1
InRoom
Controller
.
The bus address or bus ID is adjusted with the dip-switches on the IOC. The table at the
right shows the corresponding adjustment for all possible bus IDs. The counting begins
with 0 and ends with 31. A "1" means a dip-switch is in the ON position.
On an InRoom Controller the bus-ID is adjusted in the global status line (See chapter
5. Controller Start).
An IOC is delivered with the ID 01 as standard, an InRoom Controller has the ID 31 as
standard. After having provided all units (IOCs) with a different bus-ID, the units must
be declared as participants of the bus, for the bus exists up to now only physically. (See
next page).
To control the presence of each bus member, type
iobus and you will see a list as
follows:
ID type status availability
00 unknown passive 000
01 IO-controller active 255
02 unknown passive 000
03 IO-controller active me
JP1 Pos.1-2!
JP1 Pos.1-2!
Bus termination:
InRoom
Jumper X2 on InRoom
Controller
:
Controller board in
position A
IOC: Jumper 1 in pos. 1-2
terminals
on IOC
terminals
on IOC
In short:
1. Connect units by bus lines
2. Set bus terminations (beginning/end)
3. Adjust bus-IDs
4. Generate bus configuration (declare participants)
Screen
4. Bus communication
- Operating Instructions 1
- Contents 3
- 1. Presentation of the system 5
- 2. Hardware components 6
- 2.2.1 Board design 9
- 2.2.2 Assignment - EDIO1 10
- 2.2.3 Assignment - EDIO2 11
- 2.3.1 Board design 12
- 2.3.2 Assignment - EAIO 13
- 2.4.2 Assignment - EBUS 14
- 2.4.1 Board design 14
- 2.5 InRoom Controller Board 15
- 3. Operator interface 16
- 4. Bus communication 19
- 4.2 Special cases 20
- 5. Controller start 21
- Stop states 23
- Symbols for operating states 23
- Symbols for alarm messages 23
- Passwords 24
- 6. Operation 25
- 6.1.2 Info overview 26
- Display 28
- Data logger 28
- 6.2 Control level 32
- 6.2.2 Control commands 33
- A B C 34
- D E F 35
- Display Cooling 37
- Display Cooling 38
- Display Valves 39
- Display Valves 40
- Times are entered in seconds 41
- F3 F5 F6 44
- Display Humidification 45
- Humidification 46
- Dehumidification (Part 2) 47
- Display Air 49
- Is the minimum speed kept ? 50
- Display Air 52
- Function 52
- AT-Preferences 53
- Password 53
- K L M 54
- N O P 55
- Q R S 56
- T U V 57
- Display Heating 62
- Display Equipment 65
- Display Equipment 66
- Gen. settings 68
- Display Gen. settings 69
- Display Gen. settings 70
- Gen. setting 71
- Display Day & Night 72
- Due to 75
- Commands 76
- Display Data 78
- Maintenance 79
- Manual Operation 80
- 6.4 Default configurations 81
- General alarms 82
- Limit alarms 82
- Week program 82
- Components 83
- Drycooler 84
- Humidifiers 85
- Dehumidifier 86
- Sensors (continued) 88
- External alarms 88
- Actual value output 88
- 6.4.1 Preconfigurations 89
- 7. Alarm treatment 90
- 7.2 Alarm messages 91
- 7.3 Component-related alarms 92
- 7.4 Alarm Reset 92
- 8. Configuration notes 94
- 8.1 Loading new Software 95
- InRoom - Service 96
- 9. Network Management Card 97
- BOOTP and DHCP configuration 98
- Control console 101
- 9.2 Access a Configured Unit 102
- Telnet/SSH 103
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji